=============================================================================
Intel(R) Server Platforms SE7520JR2 BMC RELEASE NOTES
=============================================================================
INTEL Enterprise Platform & Services Marketing
Intel Corporation
2111 N.E. 25th Avenue, Hillsboro, OR 97124 USA
=============================================================================
DATE:		June 14, 2005
TO:		Intel(R) server platform SE7520JR2 customers
SUBJECT:	BMC(R) 0.48 Release Notes
=============================================================================
                               LEGAL INFORMATION
=============================================================================
Information in this document is provided in connection with Intel products. 
No license, express or implied, by estoppel or otherwise, to any intellectual 
property rights is granted by this document. Except as provided in Intel's 
Terms and Conditions of Sale for such products, Intel assumes no liability 
whatsoever, and Intel disclaims any express or implied warranty, relating to 
sale and/or use of Intel products including liability or warranties relating 
to fitness for a particular purpose, merchantability, or infringement of any 
patent, copyright or other intellectual property right. Intel Corporation may 
have patents or pending patent applications, trademarks, copyrights, or other 
intellectual property rights that relate to the presented subject matter.  
The furnishing of documents and other materials and information does not 
provide any license, express or implied, by estoppel or otherwise, to any 
such patents, trademarks, copyrights, or other intellectual property rights.  
Intel products are not intended for use in medical, life saving, or life 
sustaining applications. Intel may make changes to specifications and product 
descriptions at any time, without notice.

Intel is a registered trademark of Intel Corporation. 

*Other names and brands are the property of their respective owners.

Copyright (c) 2005 Intel Corporation.

=============================================================================
                              ABOUT THIS RELEASE
=============================================================================
REVISION INFORMATION RETURNED BY GET DEVICE ID COMMAND:

Operational mode:	v00.48
Flash update mode:	v00.11
PIA data:		v01.57
Manufacturer ID:	0x000157 (Intel)
Product ID:		0x0022 (SE7520JR2)

Checksum Information:
Operational Code
  Region:		0x00030000 -> 0x000dc19a
  Checksum:		0xaf4e
Boot Block
  Region:		0x00000000 -> 0x00003052
  Checksum:		0x543a

=============================================================================
			SYSTEM HARDWARE REQUIREMENTS/REVISIONS
=============================================================================
Intel(R) Management Module(IMM):
  - Advanced Edition PBA C44973-405 or higher with BMC 0.23 or higher
    installed.

  - Professional Edition PBA C46194-301 or higher with BMC 0.23 or higher
    installed.

Advanced Edition NIC board (GCM):
  PBA C44941-201 (or later)

Server Board SE7520JR2 with the following PBA revisions (or higher):
  C53659-301 
  C53660-404
  C53661-601
  C53662-503

=============================================================================
		       SYSTEM SOFTWARE REQUIREMENTS/REVISIONS
=============================================================================
- SE7520JR BIOS revision:
  SE7520JR22.86B.P.05.00.0067.111820041003 (or later) 
  Any BIOS version prior to these will cause the BMC serial channel to not
  function properly.

- SE7520JR2 FRU/SDR package:
  JR-6.6.3 or later

- PC87431M mini-Baseboard Managment Controler (mBMC) from National Semiconductor:
  Revision 2.40
 
- Firmware revisions on the Advanced Edition IMM card:
  FPGA : rev 47 (or later)
  EDID: rev 04
  Any version prior to these will cause the Keyboard and mouse to become
  non-functional.
  The KVM viewer application will also not function properly with earlier
  FPGA versions.

=============================================================================
                         IMPORTANT INSTALLATION NOTES
=============================================================================
- The following files are necessary to update the firmware:
  Run.bat	- Batch file used to update the firmware
  7520JR48.hex	- BMC 0.48 firmware hex file for the SE7520JR2 platform
  FWPIAUpd.exe	- DOS utility to program firmware hex file into the flash device
		  Prior versions of this utility will not work with this FW

Executing the fwpiaupd utility with your own command switches is unsupported 
and may leave your baseboard in a non-operational state! Please use the
provided batch file to update the firmware.

Executing the batch file can be done from any media (Hard disk, USB disk-on-key,
shared network drive or floppy).

BMC 0.23 or later must be preinstalled.
If this is not the case, please update the IMM firmware to BMC 0.23 before
updating to this release.

The boot block has been changed with the BMC 0.31 release but it is not
required for this release. The batch file provided with this BMC package
does not update the boot block.

=============================================================================
                         INSTALLATION PROCEDURE
=============================================================================
- If this update is not being applied to BMC 0.23 or later, please first 
  update to 0.23.
- Copy the update files from this release package to the 
  media(Hard Drive, USB Disk-on-Key, Floppy...) that you wish to perform
  the update from. Files include:  run.bat, 7520JRxx.Hex, FWPIAUpd.exe,
- Execute the run.bat file to begin the firmware update process (if running
  from the Software Update package, select update IMM Firmware option)
- Install the webserver EFS image revision 1.20 by either running upd_efs.bat
  (if running from the Software Update package, select update EFS 
  Webserver option) or by uploading the efs_120.efs file using the web server
  at URL http://xxx.xxx.xxx.xxx/!@efsUpdate. Replace the xxx.xxx.xxx.xxx
  with the IP address used to configure the HTTP web server feature.
  Please use the provided batch file as it contains the necessary -nopc 
  command line switch to FWPIAUPD.exe to successfully update the EFS area.
- Proceed to install the latest FRU/SDR package.

=============================================================================
                           KNOWN ISSUES/WORKAROUNDS
=============================================================================
- This and all future firmware releases will only support the fab -3xx 
  and later Professional and Advanced IMM.
  Fab -2xx and prior modules are no longer supported!

  See the SYSTEM HARDWARE REQUIREMENTS section above for details.

- Please clear the web browser cache if the web server feature was used prior
  to BMC 0.37 as these cached pages will conflict with the pages generated
  with versions after BMC 38 and EFS content rev 1.12.
  The clearing of the web browser cache need only be done once.

=============================================================================
                           FEATURES ADDED
=============================================================================

BMC 0.48:
- None

BMC 0.47:
- None

BMC 0.46:
- None

BMC 0.45:
- None

BMC 0.44:
- None

BMC 0.43:
- None

BMC 0.42:
- None

BMC 0.41:
- None

BMC 0.40:
- None

BMC 0.39:
- None

BMC 0.38:
- None

BMC 0.37:
- None

BMC 0.36:
- None

BMC 0.35:
- None

BMC 0.34:
- None

BMC 0.33:
- None

BMC 0.32:
- None

BMC 0.31:
- Support for Telco Alarm Manager hardware

BMC 0.30:
- None

BMC 0.29:
- None

BMC 0.28:
- None

BMC 0.27:
- None

BMC 0.26:
- None

BMC 0.25:
- None

BMC 0.24:
- None

BMC 0.23:
- None

BMC 0.22:
- None

BMC 0.21:
- None

BMC 0.20:
- None

BMC 0.19:
- None

BMC 0.18:
- Re-enabled FRB3 support

BMC 0.17:
- None

BMC 0.16:
- None

BMC 0.15:
- None

BMC 0.14:
- None

BMC 0.13:
- None

BMC 0.12:
- None

BMC 0.11:
- Supports the controlling of the fan FRU LEDs.
- Support for sensors in web pages
- Support for updating the EFS area with the fwpiaupd.exe utility

BMC 0.10:
- Email alerts now using using human readable SEL format
- Added DNS support to SMTP feature

BMC 09:
- Support for TControl
- Added chipset drivers.
- Last phase of Fan control/monitoring
- Support for fan presence and hot-swap fans.
- CLI commands for SEL using human readable format

BMC 08:
- KVM
- Auto Server Shutdown
- Human Readable SEL in the web server
- First phase of fan control

BMC 07:
- PSMI support
- GCM I2C bus speed increased to 400kHz
- PC87431 (mBMC) support
- Sahalee BMC FRU device 0 support

BMC 06:
- Memory RAS feature added
- Support for Platform and Instance Identification
- Support for DNS
- Support for reporting uncorrectable front side bus and memory errors
  (i.e. SMI Timeout post-mortem)
- Added webpage support for SEL.

BMC 05:
- Initial implementation of PIA phase 2 infrastructure.
- Added FPGA I2C driver.
- Firmware is now configured to use the TE28F320 4Mb flash map.
- Added support for fan PWM control.

BMC 04:
- SNMP
- IMM identification
    Added advanced Feature Support parameter in PlatInfo configuration
    Added feature support module to support IMM and Platform identification
    support.
- Added feature OEM feature parameter in LAN configuration

BMC 03:
- Serial channel
- RMCP+ 
- SOL 2.0
- Added support for BMC FRU device 2 which is the Advanced Edition IMM NIC FRU.

BMC 02:
- Added user authentication and IPMI configuration to web server.

BMC 01:
- First release after power on code.

=============================================================================
                           ISSUES FIXED
=============================================================================

BMC 0.48:
-DCS:19924
 IMM does not respond to HTTP requests
-DCS:20194
 BMC TAM WDT alarms being cleared on power off
-DCS:41528
 [LNc] IMM CLI commands do not include ALARM
-DCS:21113
 Enable 1MHz I2C speed on FPGA
-DCS:20049
 Clicking the 'last' button displays incorrect number of records per page.
-DCS:20144
 Incorrect 'Available entries' on the SEL pages
-DCS:20123
 Clicking on 'Previous' button displays incorrect no. of entries from last page.
-DCS:20210
 HTTP: Incorrect SEL percentage displayed on both the SEL pages
-DCS:20664
 CLI overwrites commands when connected on a embedded telnet session 
-DCS:19661
 BMC21/Telnet: Backspace is causing error in telnet
-DCS:42163
 KVM support info in FW not correct
-DCS:20840
 Unable to login as a non-null user using DPCCLI with Jarrell BMC46. 
-DCS:40056
 ARP suspension occurs even when the watchdog is restarted 
-DCS:40056
 ARP suspension occurs even when the watchdog is restarted 
-DCS:40234
 apiKey.tcl:1: Set Channel Security Key not implemented 
-DCS:41691
 Junk characters showed in the screen while the systems is booting 
-DCS:41885
 Telnet/CLI: missing space in interrupt help  
-DCS:41888
 Telnet/CLI: interrupt command not functional
-DCS:40132
 BMC21/Telnet: Prompt setting is not working in telnet 

BMC 0.47:
- DCS: 42200
  Fix for #20373 created another issue (DR#42200) which has been resolved
- DCS: 42362 
  A memory leak in the web server has been resolved
- DCS: 19930 
  Self test errors with IMM Pro; changes that are made for the NCR SOL issue

BMC 0.46:
- DCS: 19438
  Invalid Chassis information and Asset tag  in the 'System Summary' page. 
- DCS: 19850
  Host and domain name updates not successful.
- DCS: 19878
  Gateway IP not getting reflected on the Summary page. 
- DCS: 20076
  False front panel temp lower critical events generated 
- DCS: 20194
  BMC TAM WDT alarms being cleared on power off 
- DCS: 20373
  When user creates a session with USER access, they can run any admin command 
- DCS: 41879
  Telnet/CLI: entering character after valid password "IPMI Session Error" 
- DCS: 41920
  No LAN functionality 
- DCS: 42158
  Watchdog timer test causes FRB timeout failure
- DCS: 76110
  Jarrell FRUSDR 6.6.1-Unexpected sel events for Temp Sensors,
  Power Unit and Terminator
- DCS: 76154
  POST Codes Not Driven by SIO on UUT3

BMC 0.45:
- DCS: 41857
  (X) Power On/Off (warm reset) test hangs at Post C ode 13 or F8  
- DCS: 42201
  Harwich CLI and SOL redirection loses connection frequently  

BMC 0.44:
- DCS: 20125
  KVM : Not able to see video redirection on Jarrel Fab 503 board.

BMC 0.43:
- DCS: 20229
  HTTP: 'Configuration' page fields could be set with 'User' privilege level.  

BMC 0.42:
- DCS: 16837
  FW: User Feature cmd for HTTP/S enables returns incorrect # of data bytes 
- DCS: 20132
  BMC fails self test err #8300
- DCS: 20140
  Multiple email alerts are observed for single SEL entry
- DCS: 20194
  BMC TAM WDT alarms being cleared on power off 
- DCS: 20213
  SCW: There are some errors observed at the end of SCW configuration.
- DCS: 20268
  BMC stops responding very often - Jarell 
- DCS: 20307
  Telnet: Invalid Password leads to BMC reset 

BMC 0.41:
- DCS: 20132
  BMC fails self test err #8300
- DCS: 20140
  Multiple email alerts are observed for single SEL entry
- DCS: 20173
  HTTP: Changing UsrUrl2 adds special characters
- DCS: 41534
  SNMP: SNMPGet of SDR returns wrong values 
- DCS: 41678
  SMTP: Two emails received for the same event

BMC 0.40:
- DCS: 20078
  BMC loses connectivity with KVM Viewer and launching ISM  
- DCS: 20115
  Updating or reading GCM FRU data fails nearly 30% of attempts 

BMC 0.39:
- DCS: 19073
  BMC not responding going across sub-nets for Adv IMM card
- DCS: 19881
  BMC38/Telnet: BMC has become busy(CC is 0xC0), not coming out of this state
- DCS: 19376
  KVM -Rebooting  the system with KVM session active will lock the local  Mouse
- DCS: 19844
  CGI config byte reset to 00
- DCS: 19846
   Web server hangs on clicking ""Clear SEL"" on the page.
- DCS: 19402
  SEL page in EFS content rev 1.6 has errors
- DCS: 19827
  Embedded CLI/SOL functionality is inconsistent and does not display correctly
- DCS: 19690
  Web Server SEL View erratic
- DCS: 19377
  KVM - Mouse control not returned back to Local server.
- DCS: 19891
  SNMP Enable bit resets with power cycle
- DCS: 19454
  SEL page does not display the entries.
- DCS: 19860
  BMC38/Telnet: telnet and HTTP are not working when telnet port is changed
- DCS: 19861
  PS1 Status on the Summary page shows ""Inst"" for ""Installed"".
- DCS: 19880
  BMC38/Telnet: login propmt should not come when all 4 telnet sessions are active
- DCS: 19850
  Host and domain name updates not successful.  
- DCS: 19878
  Gateway IP not getting reflected on the Summary page
- DCS: 19879
  Host name and Domain name should be clear on the Summary page.  
- DCS: 19438
  Invalid Chassis information and Asset tag  in the "System Summary" page.
- DCS: 19880
  BMC38/Telnet: login propmt should not come when all 4 telnet sessions are active 
- DCS: 19881 
  BMC38/Telnet: BMC has become busy(CC is 0xC0), not coming out of this state  
- DCS: 74756
  FAN 5 and FAN 6 sensor numbers get swapped when IMM installed
- DCS: 19073
  BMC not responding going across sub-nets for Adv IMM card
- DCS: 19881
  BMC38/Telnet: BMC has become busy(CC is 0xC0), not coming out of this state
- DCS: 19846
  Web server hangs on clicking ""Clear SEL"" on the page.
- DCS: 19376
  KVM -Rebooting  the system with KVM session active will lock the local  Mouse
- DCS: 19891
  SNMP Enable bit resets with power cycle
- DCS: 19844
  CGI config byte reset to 00
- DCS: 19850
  Host and domain name updates not successful.
- DCS: 19438
  Invalid Chassis information and Asset tag  in the ""System Summary"" page.
- DCS: 19402
  SEL page in EFS content rev 1.6 has errors
- DCS: 19377
  KVM - Mouse control not returned back to Local server.
- DCS: 19454
  SEL page does not display the entries.
- DCS: 19690
  Web Server SEL View erratic
- DCS: 19723
  [x] Chassis intrussion not being logged in the SEL when opening the side cover
- DCS: 19878
  Gateway IP not getting reflected on the Summary page.
- DCS: 19879
  Host name and Domain name should be clear on the Summary page.
- DCS: 19860
  BMC38/Telnet: telnet and HTTP are not working when telnet port is changed"
- DCS: 19861
  PS1 Status on the Summary page shows ""Inst"" for ""Installed"".
- DCS: 19880
  BMC38/Telnet: login propmt should not come when all 4 telnet sessions are active
- DCS: 19492
  Email Alert is not working for 4 configurations
- DCS: 19585
  LANDesk reports that mux is getting stuck in SYSTEM mode at BIOS POST end
- DCS: 19862
  Alerts not generated for configured filters
- DCS: 19882
  Error while accessing power control and SEL details in EFS web page
- DCS: 19937
  SEL pages not working after few hours of loading BMC 1.39, EFS 1.13
- DCS: 39766
  SDR Clear does not cancel reservation
- DCS: 38098
  SDR EraseTime timestamp Is Not Expected Time Value
- DCS: 74762
  Sometimes BMC will disable event messages from threshold type sensors after A/C off then on
- DCS: 76109
  Sometimes BMC will disable event messages from threshold type sensors after A/C off then on
- DCS: 19654
  Issues with SEL view range in the web server
- DCS: 19840
  Unnecessary characters appear on the left panel in Mozilla.
- DCS: 19882
  Error while accessing power control and SEL details in EFS web page
- DCS: 19907
  SOL: Accepted Character Count field is wrong.
- DCS: 19933
  Issues with automatic refresh of SEL pages and default no. of entries.
- DCS: 19937
  SEL pages not working after few hours of loading BMC 1.39, EFS 1.13
- DCS: 19956
  Issues with ""Next"" button on the ""System Event log/SEL details""  page.
- DCS: 19958
  Issues with ""Previous"" button on the ""System Event log"" page.
- DCS: 19959
  Issues with ""Previous"" button on the ""SEL details"" page.
- DCS: 19969
  embedded web server gives error if cli accessing BMC
- DCS: 19880
  BMC38/Telnet: login propmt should not come when all 4 telnet sessions are active
- DCS: 19881
  BMC38/Telnet: BMC has become busy(CC is 0xC0), not coming out of this state
- DCS: 19937
  SEL pages not working after few hours of loading BMC 1.39, EFS 1.13
- DCS: 19943
  SOL: SOL payloads jam indefinitely. Operation Status = 0x40
- DCS: 20013
  HTTP : After working for around 2 - 2.5 hrs, Found issues with  SEL details page
- DCS: 20038
  DC power cycling is causing network stack to become unavailable.
- DCS: 40062
  Cipher Suite Id 7 & 8 failed to establish a session
- DCS: 40063
  Cipher Suite Id 7 & 8 failed to establish a session
- DCS: 40139
  FSC system booting with 19+ SEL entries
- DCS: 41353
  Telnet 'power -console' fails to show server screen
- DCS: 41588
  SNMP fails to change ports
- DCS: 76000
  FRB2 was not disabling the BSP when the SEL log was full
- DCS: 19912
  System fails to boot with Riggins Base, P06 BIOS & IMM
- DCS: 74773
  Brandon Fab7 board+ SC5300 base chassis+ IMM (professional version module),
  server system can not power up and have 1-5-4-4 beep warning.
- DCS: 19888
  Fix for data entry format in the IPMI command window.
  It now accepts things like "20 18 1" as well as "20 18 01".
- DCS: 20041
  Enabled the ability to write to the power unit and power supply FRU devices

BMC 0.38:
- DCS: 17571  
  HTTP web server about link causes error 
- DCS: 19402  
  SEL page in EFS content rev 1.6 has errors 
- DCS: 19454
  SEL page does not display the entries
- DCS: 19475
  ctWrong completion code returned for invalid commands in the web page
- DCS: 19558  
  [IMM] Status LED does not return to green from amber
- DCS: 19616
  Fan status LED does not go out after hot swap fan is repaired 
- DCS: 19628
  BMC35/Telnet: Telnet is not working for any other port  
- DCS: 19647
  Incorrect data in the SEL record displayed in the SEL page
- DCS: 19654  
  Issues with SEL view range in the web server
- DCS: 19659
  Wrong "Current power state" shown on the "Power Control" page
- DCS: 19678  
  Embedded web server "Help" link is broken 
- DCS: 19679
  Unexpected character on web server summary page 
- DCS: 19682  
  Dislplay IMM GCM NIC gateway and subnet mask on summary page 
- DCS: 19690
  Web Server SEL View erratic 
- DCS: 19737  
  Unable to telnet for user1 when password is reset 
- DCS: 19801
  Event receiver not set correctly in SATA HSBP after AC cycle 
- DCS: 19824
  Inconsistent mouse and keyboard control on KVM 
- DCS: 19825  
  Power cycling on can cause the BMC to not allow further connections 
- DCS: 19826
  Logging into embedded CLI while KVM ena bled causes BMC reset 
- DCS: 19828  
  Embedded CLI Banner still reads Sahalee BMC Embedded Telnet 
- DCS: 19833  
  Updating NIC configuration during Telnet Session stops LAN interface 
- DCS: 19836  
  Sessions and stress test issues with the web server

BMC 0.37:
- DCS: 19402
  SEL page in EFS content rev 1.6 has errors  
- DCS: 19439
  No data available in the product area of the web page.
- DCS: 19452
  SEL page does not display the entries.  
- DCS: 19497
  Help pages missing in the Embedded web server.  
- DCS: 19534
  EFS Updates failing 
- DCS: 19628
  BMC35/Telnet: Telnet is not working for any other port  
- DCS: 19647
  Incorrect data in the SEL record displayed in the SEL page.  
- DCS: 19654
  Issues with SEL view range in the web server.  
- DCS: 19670
  /!@efsUpdate page can be accessed/executed by any privilege level.  
- DCS: 19677
  "About" box for embedded Web Server copyright date  
- DCS: 19678
  Embedded web server "Help" link is broken  
- DCS: 19679
  Unexpected character on web server summary page  
- DCS: 19680
  Embedded Web Server has ( ) behind DIMMS, etc 
- DCS: 19681
  Remove "product" from web server summary page
- DCS: 19683
  Web Server failure needs to be in Red  
- DCS: 19684
  Web Server summary page needs to show "RPM"  
- DCS: 19690
  Web Server SEL View erratic 
- DCS: 19732
  HTTP does not work for any port other than 80  
- DCS: None
  Sensors that are valid only while DC is on were being scanned
  while DC was off.
- DCS: None
  Separated the PCI HP module set for Harwich as these were conflicting with
  the SE7520AF2 PCI hot plug sensor enumerations.
- DCS: 40239
  Added support for Harwich in the platform mismatch command.

BMC 0.36
- DCS: 39809
  Added new signals in MCH driver
- DCS: None
  Web server enhancements from TME/PME review feedback
- DCS: None
  Moved creation of new command tables to external RAM due to running out
  of internal RAM.

BMC 0.35
- DCS: 19444
  BMC32 Clearlog -state command in Telnet is not behaving as expected  
- DCS: 19468
  BMC32/Telnet: displaylog is not working with "-s" option  
- DCS: 19488
  BMC Prochot monitoring by BMC not reliable 
- DCS: 19482
  Could not connect to the web server in SE7520JR2 BMC 33..
- DCS: None
  Fix for mouse and keyboard getting disabled during system reboot or reset.
- DCS: 19535
  Front Panel reset button not getting locked in Sleep S1state
- DCS: 19493
  BMC33/Telnet: telnet is not working with BMC33

BMC 0.34
- DCS: None
  All advanced IMM features to not work with BMC 0.33
- DCS: 19530
  Get HTTP Configuration Parameters-- Parameter Revision is not 0x11  
- DCS: 19485
  BMC to emulate keyboard / mouse correctly on Win2003 
- DCS: 19494
  Key Board Gets Disabled on Win2000
- DCS: 39476
  Serial over LAN recieved unexpected successful response

BMC 0.33
- DCS: None
  HTTP web server fixes
- DCS: 17503
  Get SNMP Config Params command returns bad completion code
- DCS: 39454
  SMI timeout does not work
- DCS: 39489
  OEM1 bit is un-settable
- DCS: None
  KVM fixes
- DCS: 18215
  Init Agent fails to initialize the sensor thresholds
- DCS: 16670
  HTTP Power Webpage, timestamp needs to be updated
- DCS: 19402
  SEL page in EFS content rev 1.6 has errors

BMC 0.32
- DCS: 17950
  [IMM] Boot Initator info Block seemingly not validated 
- DCS: 19398
  PDB failure status not logged by BMC
- DCS: 15895, 16213, 16597, 16840, 17179, 18805, 19246, and 19321
  Miscellaneous HTTP web server fixes

BMC 0.31
- DCS: 16325
  EMP is not available for 10 seconds after DC ON  
- DCS: 18410
  Communication failure in Terminal mode
- DCS: 19027
  Failed to make direct serial connection (LSM)  
- DCS: 19028
  Failed to establish Serial Modem Connection (LSM)  
- DCS: 19031
  [IMM] SecureModeActive bit is not set by the Secure Mode KB signal.  
- DCS: 19306
  CRERR04 - during console redirection and EMP is enabled
- DCS: 19354
  Enable Telco Alarm Manager feature in Jarrell BMC (IMM)
- DCS: 19363
  BMC 30:SMTP -Parameter Revision is not 0x11 
- DCS: 19369
  SMTP config parm#6, DNS override, inverted 
- DCS: 75975
  [J1-IMM] BMC did not lock the Power and Reset push-buttons when Secure Mode
  signal is asserted.
- DCS: None
  Add support to allow the SE7520JR2 BMC firmware to execute on a SHW4 server

BMC 0.30
- DCS: 15819
  IPMI2.0 commands not implemented correctly.
- DCS: 16415
  KVM - Get Video Status requires video data structure
- DCS: 16634
  FW: Setting an SMTP configuration appears to set multiple configurations
- DCS: 16837
  FW: User Feature cmd for HTTP/S enables returns incorrect # of data bytes
- DCS: 17186
  Get Channel Payload Support responses the same output
- DCS: 17459
  KVM - Set KVM Config. to set in progress results in invalid completion code
- DCS: 17460
  KVM - issuing Set KVM Configuration to disable KVM does not work.
- DCS: 17501
  KVM - Activate Payload not returning all required bytes
- DCS: 17502
  KVM - Video Status incorrectly reported when powered off
- DCS: 17503
  Get SNMP Config Params command returns bad completion code
- DCS: 17538
  FW:  Issues with Set SMTP Config Params command
- DCS: 17540
  FW:  Issues with Set/Get LAN Config Params cmd w/ parameter 0xc4
- DCS: 17773
  KVM - No Video Data Received
- DCS: 17779
  KVM - Video packets still sent after Payload Deactivated
- DCS: 17815
  KVM - Invalid Mouse Type reported
- DCS: 17860
  KVM - BMC Becomes unresponsive to LAN connection
- DCS: 17863
  KVM - Capture Reference Frame has too much data in it
- DCS: 17865
  KVM - System will not boot w/KVM session Active
- DCS: 17949
  LAN: chan 3 MAC Addr not auto-populated
- DCS: 18387
  [IMM] Front Panel LCP is not discovered.
- DCS: 18698
  Status LED does not turn amber when there is a fault on the system
- DCS: 19169
  Restart Cause command is not working as expected
- DCS: 19237
  PCI Hot Plug sensors stuck in init update mode after exit FW-Xfer mode
- DCS: 19239
  [IMM] IERR occured at  AC power cycle test.
- DCS: 19267
  BMC29:Power control fault beep codes are emitted when repeated power cycles are
- DCS: 19299
  LAN Alerts with Alert strings are reported as malformed packets
- DCS: 19321
  EFS format/content not finalized yet
- DCS: 19324
  Mouse / Keyboard Not Initialized when OS booted during  a KVM session
- DCS: 19326
  FPGA Encryption Problematic - After 100 + packets video data length is invalid

BMC 0.29:
- DCS: 19155
  BMC doesn't correctly transition to S1 sleep state
- DCS: 34955
  To implement Memory board Front and rear temperature sensors
- DCS: None
  Better handling of power loss & DC off events.
- DCS: 19139
  Console Redirection Causes Firmware Progress Errors in LD  
- DCS: 38307
  System failed to log AC power failure during boot
- DCS: 19107
  BMC 0.28 Encountered failure while verifying sensor initialization value.  
- DCS: 18875
  Online Firmware Update causes BMC to hang 
- DCS: 19156
  RQ_SyncSMBus command locking wrong bus  
- DCS: 18963
  PS_PWR_GD ISR is not being enabled occasionally
- DCS: 18215
  Removed init agent changes that were causing other problems.
- DCS: 18936
  [IMM] IERR event is always occur right after AC on
- DCS: 19135
  mBMC update with IMM installed fails on Alief and Brandon
- DCS: 16483
  BMC and SDR updates fail 
- DCS: 75901
  DC cycling failed with IMM cards installed (Procs go offline)
- DCS: 75907
  Processors being Disabled after an OS Restart
- DCS: 75908
  Problems Powering On after an OS Shutdown
- DCS: 75915
  BMC25 is shutting down immediately after loading and disabling the processors
- DCS: 74593
  BIOS B19~P03 versions cause UUT boot failed after several front panel power
  cycling while IMM card installed.
- DCS: 74618
  IMM fails in Brandon -601A SCSI

BMC 0.28:
- DCS: 18866 & 18867
  Thermal Trips were calling power control code to power down system. This
  functionality is handled directly by the hardware.
- DCS: None
  Added new module selection for Memory Board
- DCS: None
  Fans would sometimes indicate failure at DC on.
- DCS: 19066
  PCI Hot Plug Sensors do not show up 
- DCS: None
  Power supplies from shutting down due to current spikes caused by fan speed
  changing to quickly.
- DCS: None
  Processors are getting enabled and disabled twice during FRB3 failures.
- DCS: None
  ID LED on would get locked on when button is pushed during power state
  transitions.
- DCS: 18883
  OOB connection not working out of subnet 
- DCS: 19054
  Repeat issuance of CLI power actions causes IMM to stop responding 
- DCS: 19056
  Thermal Trips being seen during DC power cycle testing 
- DCS: 19072
  1-5-4-4- beep code 
- DCS: 19083
  CLI lockup on power commands with BMC A.27 engineering release  
- DCS: 19084
  BMC a.27 causing therm trip and IERR errors on Brandon and Jarrell 

BMC 0.27:
- Only released as incremental developer drops to verify resolutions that are
  in place with the BMC 0.28 release.

BMC 0.26:
- DCS: 19010
  Self test error with LSM Linux Console 
- DCS: 18875
  Online Firmware Update causes BMC to hang 
- DCS: 19056
  Thermal Trips being seen during DC power cycle testing 
- DCS: 19016
  Temporary failure of boot 
- DCS: 18215
  Init Agent fails to initialize the sensor thresholds
- DCS: None
  Added some kick start ramping, but then went to a fixed 50% kick start.
- DCS: 19066
  PCI Hot Plug Sensors do not show up  
- DCS: 38317
  BMC release process not producing repeatable checksums
- DCS: None
  Changed to notify waiting task if multiple loss of arbitration detected,
  regardless of task state.
- DCS: 18963
  PS_PWR_GD ISR is not being enabled occasionally 
- DCS: 19019
  Rapid, succesive activation of the Power button, hangs BMC  
- DCS: 19054
  Repeat  issuance of CLI power actions causes IMM to stop responding 


BMC 0.25:
- DCS: 18963
  PS_PWR_GD ISR is not being enabled occasionally 
- DCS: 18638
  BMC22: OnlineUpdateOpenArea is returning 0x00 as CC when it should not return so
- DCS: None
  Fix for LAN channels not working after an exit firmware transfer mode
- DCS: 18875
  Online Firmware Update causes BMC to hang 

BMC 0.24:
- DCS: None
  Fixed a defect in the VERIFY macro
- DCS: None
  Added support for using a manufacturing test SDR
- DCS: None
  HW team reporting fan circuit FETs being blown due to LM93 PWM outputs being
  driven while DC is off
- DCS: None
  If the private store gets cleared both processors will come up as disabled
  by FRB3 on the next boot
- DCS: 18208
  [IMM] CF9 hard reset does not work 
- DCS: None
  mBMC Driver potential error fix
- DCS: None
  HW folks have the nominal, boost & sleep values set to FCh in the SDRs
  which is wrong.
- DCS: 18217 & 18551
  Implement a bi-color system fault indicator
  (follow-up: counter-act the mBMCs clearing of the LEDs on DC power on)
- DCS: None
  Added defines to nullify printf in release mode
- DCS: 18806
  BMC generates Self Test Error/ Parity Error with LanDesk SOL console 
- DCS: None
  Added support for using a shipping, TDE Adv IMM and TDE Pro IMM SDR.
- DCS: 18217
  The comment describing the mBMC color conversion value assumptions was incorrect
- DCS: None
  Found a memory leak in mactconet.c
- DCS: None
  mBMC Driver reduce number of retries
- DCS: 18461
  HDD LED on front panel is red when IMM is installed 
- DCS: None
  Incorporate the latest FSC spreadsheet data into the LM93 register defaults
- DCS: None
  Added support for handling the IPMI requests Set ACPI Power State 
  and Get ACPI Power State through the SMM channel.
- DCS: None
  mBMC Driver parameter tweaking to increase performance 
- DCS: 18866
  [IMM] Thermal trip event is not logged in SEL
- DCS: 18867
  [IMM] IERR event is not logged in SEL
- DCS: 18745
  Fans do not contribute to the overall health of the system 
- DCS: 18883
  OOB connection not working out of subnet 
- DCS: 18243
  2nd CPU fails with frb3 during post 
- DCS: 18802
  BMC failing self test corrupts BIOS information 
- DCS: 18854
  Alief BMC 23 - Resolve MAC hangs BMC 
  
BMC 0.23:
- DCS: 16967
  PET Traps were not getting detected
- DCS: 18548
  [IMM] BMC failed BIOS self test after update to  BMC version 21
- DCS: 18612
  BMC does not retain OOB connectivity after installation of ISM on server  
- DCS: 18217
  Front Panel Bi-Color LED behaviour 
- DCS: 18551
  [IMM] Status LED is not changed at  the critical event.  
- DCS: 75827
  [J1] Baseboard Management Controller Failed by Self Test command during POST
  with Sahalee FW 0.21.
- DCS: 18549
  LM93 OEM SDR would cause the BMC to hang 
- DCS: 18595
  FRUSDR version 6.2.1 Update failling with BIOS P01 and BMC 21
- DCS: None
  Added encapsulating PACKED_xxx definitions around some packed structures.
- DCS: None
  Refined the fan control for power ON and Hot swap kick Start;
  Added checks to avoid C, NC Assertions during power ON&Reset;
  Added the de-assertion Actions in the PIA for hot swap fans; Fans boost
  in the particular domain on HS fan removal
  Restored the default Nominal to half by handling the power on and HS kick
  start in the fanctrl.c code
- DCS: None
  New OEM command to restore the non-volatile configuration.
  This command needs to be called by the utility when the platform mismatch
  found during the FW update.
- DCS: None
  SensAvgCreate() would allow illegal input data
- DCS: None
  Baseboards with maximum DIMM capacity were causing systems to reset
  during POST due to the FRB3 timer expiring.
- DCS: None
  mBMC Driver message potential error fix
- DCS: None
  Multiple stack overflow issues
- DCS: None
  This check-in partially addresses clearing out bogus fan failures that are
  persistently stored.
  I have seen issues with moving my IMM between different platform types,
  where ATTNID_OK has a different value.


BMC 0.22:
- DCS: 18164
  Alief FRUSDR package 6.1.3 fails while updating FRU and SDR
- DCS: Various
  BMC fails self test.
- DCS: 18548
  [IMM] BMC failed BIOS self test after update to  BMC version 21
- DCS: Various
  New Intel OEM command 01 retrieves address of ARM exception.
- DCS: None
  Changed scaling of voltage rail current to .5A/bit from .125A/bit.
  This was to prevent possible overflow of the 8 bit sensor reading
- DCS: None
  Fixed an issue with the processor disable signals being asserted during exit
  of firmware transfer mode. On LH platforms this signal is also the SMI signal
  and was causing some strange system behavior like USB keys no longer being
  recognized.
- DCS: 18549
  LM93 OEM SDR would cause the BMC to hang 
- DCS: 75706 & 75786
  Fixed FRB issue with AC power cycling
- DCS: 16838
  Fix for Get Channel Cipher Suites Command
- DCS: 17429
  Fan Presence sensors does not detect the right fan presence
- DCS: 18437
  Default fan speed with IMM (before SDR load) is not 100%
- DCS: 18352
  NMI button on front panel was no function
- DCS: 75082
  NMI does not get generated across resets
- DCS: 17673
  FRB was not emitting a beep code when it failed final desperation mode
- DCS: 18398
  Fix for RSSP Open Session failure with Chan1/User1

BMC 0.21:
- DCS: 18423
  Button events are not being logged in the SEL
- DCS: 18415
  CLI: Internal buffer confusion when using displaylog cmd to return lots of SELs 
- DCS: 18373
  Unclear if CLI is supported over serial interface
- DCS: 17673
  FRB Algorithim Failure 
- DCS: 18374
  FRB_2 and FRB_3  ERRORS 
- DCS: 18398
  Back to back attempts to create session at different priv level fails 
- DCS: 17474
  "Resolve IP Address" command generates completion code 0xCE 
- DCS: 18333
  [IMM] After windows2K boot, SUT can not shut down completely
- DCS: 17243
  Chassis detection not working 
- DCS: 75436
  Fan RMP was still reading 644 rpm after the fan was pulled out of the  chassis
- DCS: 75601
  FRB1 and FRB3 not occurring
- DCS: 75736
  FRB3 Timer Halt Signal is incorrectly driven
- DCS: 74474
  (Sahalee) Reset period time is too long while IMM is populated.
- DCS: 74475
  P01-- BIOS POST error "Processor 01: failed FRB level 3 timer" message
- DCS: 74420
  Any type of reset results in a BIOS hang
- DCS: None
  ID LED coming on during a system power down.
- DCS: None
  Sometimes 2 power button presses are required to turn on system
- DCS: 13244
  Sysevent not being acked.
- DCS: None
  Disabling Fan sensor averaging

BMC 0.20:
- DCS: 17901
  [IMM] Not supported 'CMOS clear option' command??? 
- DCS: 18134
  Alert Immediate requests receive comp code as 0x81 
- DCS: 18303
  Fan redundancy sensors missing from all Lindenhurst products 
- DCS: 17718
  [IMM] System is powered on in a second after the power is off by POWER button
- DCS: 18197
  [SysDev-Silver] Failed acoustic sound pressure when installing IMM card  
- DCS: 18237
  [IMM] "Secure Mode" doesn't work
- DCS: 18247
  [IMM] Secure Mode signal status is reversed

BMC 0.19:
- DCS: 17905
  Power button press option does not work.
- DCS: 18195
  Byte1 mismatch in Event filter data for params 6 & 7
- DCS: 17976
  Get/Set PEF Configuration commands broken
- DCS: 18167
  Get/Set PEF Configuration commands broken
- DCS: 17994
  SOL - Attempting SOL traffic on some systems breaks LAN  
- DCS: 18239
  [IMM] BB Vbat (#1Ch) sensor always exceed limit!  
  (Also needs SDR fix)
- DCS: 18257
  POR change to add new command for BIOS to identify baseboard  
- DCS: 18216
  ChassisID Command ID off fault 
- DCS: 17718
  [IMM] System is powered on in a second after the power is off by POWER button
- DCS: 16967
  PET Traps were not getting detected
- DCS: 17810
  Network function chassis command incorrect  
- DCS: 18208
  [IMM] CF9 hard reset does not work 
- DCS: 16941
  SEL event data2 has incorrect value when sensor bridged 
- DCS: 17413
  PEF event filter table data 1 read invalid values
- DCS: None
  Added a small "context API" to IRQHand.c/.h so that runtime code can determine
  if the current context is interrupt or   timer. Modified the Threadx timer 
  module tx_tte.c to call this API so that timer context is detectable.
  Modified PIAio.c to detect timer/interrupt context during an I/O call and 
  return an error. This will need to change in the   future when PIA GPIO 
  support is added since that can function outside of task context.

BMC 0.18:
- DCS: None
  FRB timeout increased to 20 seconds.
- DCS: 17780 & 17668
  extra bytes for RAKP message 3 and error status size for RMCP+ Open Session
  response
- DCS: 15893
  BSP is not disabled when FRB2 timeout occurs
- DCS: 17730
  FRB3 does not fail when FRB3_TIMER_HALT signal deasserted
- DCS: 17851
  FRB2 timer and Late POST WDT do not work properly
- DCS: 16839
  Sahalee 2.0 Tree  Fix for SOL Payload Activation.
- DCS: 17968
  SYS_FAN_3 is not working properly
- DCS: 17810
  Moved the "chassis group control" commands 0A-0E from the chassis NetFn
  to the Intel OEM NetFn to avoid collision with new IPMI 2.0 chassis commands
- DCS: None
  This check-in addresses proper processing of error conditions
  while acquiring front panel temp sensor data.
- DCS: 17914
  [J1] The 2U fan LED doesnt work
- DCS: None
  Checking in web server and EFS image changes made by David E.
- DCS: 17474 
  Fixed Resolve IP Address command
- DCS 17806
  Failures while verifying sensor initialization values
- DCS: 17386
  Error writing to GCM FRU
- DCS: None
  Avoid processor overheat if no Tcontrol values available from BIOS or SDR
- DCS: 17149
  DIMM slot to DIMM sensor mapping is incorrect

BMC 0.17:
- DCS: None
  Added more retries in the mBMC driver to handle the I2C bus errors condition
  or mBMC delay.
- DCS: 17806
  Restart cause is unknown is most cases (also tracked by DCS 17340 & 15693)
- DCS: 34100
  Temporarily disabling FRB3 by returning FRB3_TIMER_HALT == asserted
- DCS: 17807
  "Get Chassis Status" command returns bit "power on" = 0.
- DCS: None
  Clean up the warning message
- DCS: 17005
  Increased the ARP table to 16 entries from 8. This seems to
  help the LAN failure issue but does not fully solve the problem.
- DCS: 17637
  Added check for bad pad length byte.
- DCS: 16967
  PET Traps were not getting detected
- DCS: 17882
  Implemented GetPayloadActivationCommand.
  Added implementation for "Clear Pending Requests" bit.

BMC 0.16:
- DCS: 17728
  [IMM] When SIO3 marked offline, BMC hangs
- TAO Tracker: 75417
  [J1] Get sensor reading value of 35h as IMM module was installed
- DCS: 17576
  Undocumented self test error is being logged (0x57 0x00)
- DCS: 17777
  AC power-on default for chassis ID LED is on.
- DCS: 37437
  BMC failed to power on the system after PLDs programming is completed
- TAO Tracker: 75580
  After plug in IMM Module, the SIO Fan monitor doesn't be configured suitably
- DCS: 16326
  Added the ability to update the LAN configuration in the network stack
  without restarting the BMC.
- DCS: None
  Added more retries in the mBMC driver to handle the I2C bus errors condition
  or mBMC delay. Added mBMC intrinsic signals and mBMC signal PIA records. 
- DCS: 17081
  Updated PSMI driver to read the correct v-rail current register

BMC 0.15:
- DCS: 17533
  BMC: ICMB Chassis Group Control commands return garbage
- DCS: 13492
  ICMB does not detect incorrect type/version in packet
- DCS: 17035
  Asserts in relocate.c (already fixed, these are just cosmetic tweaks)
- DCS: 17375
  Hash length for rakp message.
- DCS: 17541
  Chassis Identify command force parameter not supported
- DCS: 34100  BMC SDK Silverwood FW feature development
  seeking comments -- minor changes to Silverwood makefiles
- DCS: 16271
  NMI function does not work
- DCS: None
  Added some fixes to the FPGA I2C driver. The error handing timeouts were incorrect.
  Added some fixes to the KVM code. These are not related to actual KVM functionality
  but are needed to avoid problems with local keyboard and mouse even if KVM is not used.
- DCS: 17705
  Need driver support for the Riggins front panel temp sensor 

BMC 0.14:
- DCS: 17187 & 17188:
  Fix for RMCP+ Payload Access commands
- DCS: 17135, 17137
  PCI Hot Plug status sensor issues
- DCS 17339:
  BMC OFU: Unable to perform a FW Image Only update
- DCS: 15649:
  [IMM] NMI and ID LED don't operate
- DCS: 17340:
  BMC: Restart cause is not functioning properly
- DCS: 16272:
  BMC hangs if trying to access GCM FRU on professional card.
- DCS: None:
  Systems group requested that the LM93 fan PWM output frequencies be changed
  to 22.5KHz and the fan boost temps be changed to 91 degrees C.
  
BMC 0.13:
- CPU FRB is now functional
- DCS: 15650;
  [IMM] PowerRestorePolicy (Prior state) is not working
- DCS: 31400;
  Sahalee 2.0 Tree  Support for handling LUN02 messages within the RMCP+ module
- DCS: 17035;
  Asserts in relocate.c
- DCS: 16880;
  Platform mismatch code is locking the SEL
- DCS: 17190;
  EMP ports not working 
- DCS: 34100;
  Need a way to differentiate between Jarrell chassis.
  This check-in provide underlying support for Chassis Identification
- DCS: 16483, 16485, 16486;
- DCS: 17207;
  Disable FRB2 Action command not implemented

BMC 0.12:
- DCS: 17182;
  BMC 0.11 fails to operate on a Professional IMM
  Modified approach for external RAM discovery to examine whether FPGA is
  present or not rather than write-read test of certain RAM locations

BMC 0.11:
- DCS: 16901:
  Set Processor State command not resetting system
- DCS: 16729, 17005:
  Changed the heap creation call to take advantage of the extra external RAM
  on the advanced card. I increased the Netserv heap form 13k to 64k and the
  Netstack heap from 64k to 128k
- DCS: 16340:
  ICMB Interface not available
- DCS: 16447:
  Chassis commands dont respond after exiting FW xfer mode
- DCS# 16889:
  Change was made in the definition of the maximum capability of the stepwise
  linear fan control record.
- Main web page didnt display error if SDRs werent available
- DCS: 16390:
  Alief BMC07 does not provide minimal support on a Brandon
- Replaced IFDEFs and static constants for setting up External RAM region 
  with simple RAM discovery scheme so that 512Kb SRAM on advanced card can be used.
- DCS# 16650:  This fix will now enable BMC to log SEL events (DCS# 16655) 
  defined for RAS redundancy sensors. BMC11 will have these changes incorporated.
- Integrated latest KVM functionality.

BMC 0.10:
- Fix for RMCP+ spec issues.
 Fix for RAKP issues
 Updated RMCP+ session sequence number handling as per the IPMI2.0 spec.
- DCS: 16634 FW: Setting an SMTP configuration appears to set multiple configurations
- Fix implemented for DCS# 15932, 15935, 15937, 15956, 16687, 16689 and 16692,
  Sahalee 2.0 Tree  RMCP+ command fixes.  Payload methods were not initialized.
- Added baseboard FRU values to web server template engine.
  Fixed other minor bugs and added more checks against problems.
- DCS: 16732 Console redirect does not work on COM2/EMP
- Minor fixes to KVM functionality
- Added better handling of failed I2C transactions on FPGA pass through interface

BMC 09:
- Added code to support ClearSEL as a web command.
  Fixed IPMI command bugs described in DCS # 16419.
- Fix implemented for DCS# 16292 RMCP+ with multiple sessions.
- DCS # 16383  OFU SDR updates fail on Alief and brandon
- Fix implemented for DCS# 15924 & 34100: Memory RAS related Issues
- DCS # 16667     BMC: Initialization Agent is not getting started
- Fix implemented for DCS# 16203: SetDIMMState command failure

BMC 08:
- If there is an initialize problem that results in the FRU Table not being 
  created, the CheckAndGetFruPointer would dereference a null pointer

BMC 07:
- Fix for Memory leak in RMCP+ clients (IPMI2.0 and RAKP).
- Fix implemented for DCS#  16220, Fix for RMCP+ with valid username
- DCS: 16055 PET: Still using the platform defined variable for MANUFAC_ID
- Changed current output measurement resolution to 1/8th amp from 1/16th.
  This is because 1/16 cannot be exactly represented in an SDR scaling 
  equation but 18th can.
- The boot block was not being locked down prior to checking the forced update
  jumper and entering into firmware update mode.
- Fix implemented for DCS# (SSPD) 34100, Sahalee 2.0 Tree
  Fix for BIOS ID String in the PIA and the PIA version number
- DCS: 15817 EMP channel not available during power off
- Reduction of internal RAM usage.
  Free internal RAM has been increased to ~3000 bytes from 72.
- Fix implemented for DCS# 16203 & 34100, Set Dimm State command failure.

BMC 06:
- The private data contained with the acpi object was not being initialized.
  Resulting in the interrupt vector at address 0x0 being corrupted when an 
  acpi aware OS boots and uses the acpi power commands.
- Fixed the check for internal RAM overflow. Previously there was no warning
  if the internal RAM size was exceeded
- Fixed issue with routing network packets across subnets. 
- Fix for IPMI2.0 Get Channel Authentication Capabilities Command.
- I2C bus #3 was not enabled and reordered the I2C bus table to align with
  IPMI definitions.

BMC 05:
- Added support to not initialize the Online Update feature when a 2Mb flash
  part is detected.
- Added caching of MAC addresses on reception of UDP packets.
  This was needed so baseboard NICs can reply to UDP packets.
  The network stack was relying on ARPs to resolve all MAC addresses.
  Since baseboard NICs cannot receive ARPs we needed another way to resolve
  the MAC addresses.
- Added a check for a NULL pointer when calling pk_alloc to get a network 
  packet buffer. 
- Fix for IPMI2.0 Cipher Suite ID Command and its parameters
- While doing web page development a memory leak was found in a command failure
  case.
- Added checks for consistency between the g_SnsrAccessDef[ ] and 
  g_SnsrDeviceData[ ] tables.
- SNMP Configuration command was not disabled in IMM professional.
- Change to make sure LAN response packets are sent out the interface they came in on.
- Increased write and read cycle hold timing by one clock cycle to fix a problem
  that appears with the Actel FPGA.

BMC 04:
- Exiting firmware transfer mode, chassis resets and BMC resets were causing
  the BMC to power down the system and emit a 1-5-4-4 beep code.(DCS: 75040)
- Baseboard voltage sensors reporting incorrect values.
- Fixed IP routing for Ping. We were having a problem where we would receive 
  a ping request an channel 3 and send the response on channel 1.
- Fix for the GCM Channel not getting loaded.
- Cleaned up web server code.  Fixed bugs discovered while implementing 
  new pages.
- Fixed initialization sequencing between network stack and mactco task.
- Fixed IP routing issue. We now make sure that we send out packets on the 
  same network channel they came in on.
- Update Gratuitous ARP enable for only non-GCM channels
- Fix for the Channel Payload to work on baseboard NICs also. (External DCS# 15816) 
- The latest tip code was asserting and then overwriting the interrupt vector
  table because network features (e.g. web server, telnet, etc.) were starting
  before the network stack had initialized its buffers, queues, etc.

BMC 03:
- Abnormal behavior with features running from external SRAM.
  Still under investigation but suspect memory bus loading due to FPGA.
  Adjusted memory timing to slow down transactions.
- When loading the EFS onto a virgin system, the web server wouldnt
  select the correct set of web pages to display.  This required the EFS
  to be uploaded twice on systems that had never had an EFS image loaded.
- DCS #15736
  Flash memory library was doing unnecessary device queries during flash erase
  operations.

BMC 02:
- Chassis fans would not operate when an IMM card is installed.
- Support for only one LAN channel(7) using the Advanced Edition IMM.
  Professional Edition now supports LAN channels 1 and 2 and the Advanced 
  Edition supports three LAN channels which have been renumbered to 1, 2 and 3. 

BMC 01:
- None.

=============================================================================
                             REFERENCE MATERIAL
=============================================================================
Intel(R) Server Platform SE7520JR2 Technical Product Specification (TPS)

[END OF RELEASE NOTES]
