A:\WFW\README.TXT           DATECODE:102994                PAGE 1 of 4


This README file describes the installation of the NDIS 3 
Enhanced Mode device driver for Digital Equipment Corporation's 
EtherWORKS TURBO EISA Family of adapters in a Microsoft Windows for
Workgroups 3.11 environment.  Supported adapters include DE425. 

If you wish to use the NDIS 2 DOS Real Mode driver with Windows for 
Workgroups 3.11, please refer to the README.TXT file found in A:\ndis\dos.

The name of the NDIS 3 Enhanced Mode driver for the DE425 is 
DC21040.386

This file contains information on the following topics:

1. Installing the EtherWORKS TURBO EISA adapter
   into an existing WFW3.11 installation....................Page 2
	
2. Installing the EtherWORKS TURBO EISA adapter
   as part of a NEW WFW3.11 installation....................Page 3

3. Modifying the EtherWORKS TURBO EISA media type under
   Windows for Workgroups 3.11  (DE425 only)................Page 4


							      Page 2 of 4

   	INSTALLING THE EtherWORKS TURBO EISA ADAPTER
   	INTO AN EXISTING WFW 3.11 INSTALLATION 
  	-------------------------------------------

	Make sure your adapter is configured in the system.
	Automatic Installation Using the Network Setup Program:

	      1. Click on the Network Setup icon.

	      2. Click on the Drivers button.

	      3. If a driver for this adapter already exists, you must
		 remove it first by clicking on the driver name to
		 select the driver.

	      4. Click the Remove button to remove the old driver.

	      5. Click the Add Adapter button to add the EtherWORKS
	         TURBO EISA adapter.

	      6. Select Unlisted or Updated Network Adapter.

	      7. Insert the EtherWORKS TURBO EISA distribution diskette
		 in the floppy drive and enter A:\WFW\ 
	      
	      8. Choose the DEC EtherWORKS TURBO EISA Adapter and click OK.

	      9. Follow the instructions to complete the software
		 installation and reset or power cycle your computer 
		 when WFW asks you to restart.

							      Page 3 of 4
		 
	INSTALLING THE EtherWORKS TURBO EISA ADAPTER
   	AS PART OF A  NEW WFW 3.11 INSTALLATION
	-------------------------------------------

The installation kit for Windows for Workgroups comprises eight
diskettes.  Continue with the WFW3.11 installation of disks 1-6.
During the installation of diskette #7, the network environment
will be configured.  At this point you will be asked to select a 
Network Adapter to install.

Below is a sample of an EtherWORKS TURBO EISA Adapter 
Installation.  This example uses the default Sia_mode 
"AutoSelect" in protocol.ini.
							
Select the Bullet "Install Microsoft Windows Network"
Click OK
Click Continue

From the Add Network Adapter Screen...
Select "Unlisted or Updated Network Adapter"
Click OK

From Install Driver Screen...
-Remove disk #7
-Insert Digital EtherWORKS TURBO EISA Distribution Diskette
	NOTE:  DO NOT INCLUDE THE FILENAME AS PART OF THE PATH !!!
Type A:\wfw\
Click OK

From Unlisted or updated Network Adapter Screen...
Select "DEC EtherWORKS TURBO EISA Adapter"
Click OK

From Microsoft Windows Network Name screen...
Enter your site specific information
Click OK

From Install Driver Screen...
-Remove Digital EtherWORKS TURBO EISA Distribution Diskette
-Insert Disk #7
Click OK
-Remove Disk #7
-Insert Disk #8

From Install Driver Screen...
-Remove Disk #8
-Insert Digital EtherWORKS TURBO EISA Distribution Diskette

From Networks Screen...
Enter A:\WFW\
-Remove Digital EtherWORKS TURBO EISA Distribution Diskette
-Insert Disk #8

From Install Driver Screen...
Click OK
   .
Finish Installation 

*** Note POWER OFF/ON your EISA based PC after the install.

							       Page 4 of 4

   	MODIFYING THE ETHERWORKS TURBO EISA MEDIA TYPE UNDER
   	WINDOWS FOR WORKGROUPS 3.11  (DE425 only)
        ---------------------------------------------------

From Network Screen...
Select Network Setup Icon
Select Drivers

From Network Drivers Screen...
Select Setup...
Select Sia_Mode
Change setting to AUI
Click Set
Click OK
Click Close
Click OK
Click OK

Restart computer (POWER OFF/ON)

