-------------------------------------------------------------------
 Installing the NetWare 3/4 ODI Server Driver on NetWare 3 Servers
-------------------------------------------------------------------

This \NOVELL\SRVODI\3_1X subdirectory contains the following files:

README.TXT   - This file.
MSM31X.NLM   - Novell Media Support Module for NetWare 3 and 
	       NetWare SFT III 3.11 servers (v2.50).
LSLENH.NLM   - Novell Link Support Layer (LSL) chaining and 
	       filtering enhancement module (v1.01) that is loaded 
	       on NetWare 3.11 servers prior to loading MSM31X.NLM.
PATCHMAN.NLM - Novell Patch Manager for NetWare 3.11 servers 
	       (v2.30).  Required for LSLENH.NLM. 



			 ***TRADEMARKS***

DEC, Digital, and DECpc are trademarks of Digital Equipment 
Corporation. 

Novell, NetWare, and LAN WorkPlace are registered trademarks and 
NetWare Loadable Module, NLM, NetWare MultiProtocol Router, and 
NetWare SFT are trademarks of Novell, Incorporated.



Section 1 INSTALLING THE NETWARE 3/4 ODI SERVER DRIVER ON NETWARE 3
-------------------------------------------------------------------

You can install and use the NetWare 3/4 ODI server driver on 
NetWare 3 file servers by loading some operating system patches and 
driver support files in addition to the driver.

To install the NetWare 3/4 ODI server driver on a NetWare 3 file 
server, perform the following six steps:

I.   Verify that the network interface card (NIC) is properly
     configured and installed.  Refer to your adapter's "User 
     Information" document for instructions.

II.  Copy the NetWare 3/4 ODI server driver files to either a DOS 
     partition (Step IIA.) or a NetWare partition (Step IIB.) of 
     your NetWare server hard disk.

				     NOTE
	   The LSLENH.NLM patch should only be installed and loaded 
	   on NetWare 3.11 servers.  NetWare 3.12 does not require 
	   this patch.

     A. To copy the files to a DOS partition, enter the following 
	commands:

	1. If installing on either NetWare 3.11 or NetWare 3.12:

	      COPY A:\NOVELL\SRVODI\DC21x4.LAN C:\
	      COPY A:\NOVELL\SRVODI\ETHERTSM.NLM C:\
	      COPY A:\NOVELL\SRVODI\3_1X\MSM31X.NLM C:\

	2. If installing on NetWare 3.11 only, copy the following 
	   additional files:
	      
	      COPY A:\NOVELL\SRVODI\3_1X\LSLENH.NLM C:\
	      COPY A:\NOVELL\SRVODI\3_1X\PATCHMAN.NLM C:\
	
	You may substitute C:\ with another DOS partition and 
	subdirectory.

     B. To copy the files to a NetWare partition, you need to use 
	the NetWare 3.x Command Processor (NWSHELL). Contact Novell 
	for information on acquiring NWSHELL.NLM.  Once you have 
	NWSHELL.NLM, perform the following steps to copy the files:

	1. Load the NetWare 3.x Command Processor (NWSHELL.NLM) by
	   entering the following command at the server System 
	   Console prompt:
	   
	      :LOAD NWSHELL

	2. Change to the SYS:SYSTEM directory by entering the 
	   following command:

	      CD SYS:SYSTEM

	3. Copy the driver files to the current directory by 
	   entering the following commands:

	   a. If installing on NetWare 3.11 or NetWare 3.12:

		 COPY A:\NOVELL\SRVODI\DC21x4.LAN
		 COPY A:\NOVELL\SRVODI\ETHERTSM.NLM
		 COPY A:\NOVELL\SRVODI\3_1X\MSM31X.NLM

	   b. If installing on NetWare 3.11 only, copy the 
	      following additional files:
	      
		 COPY A:\NOVELL\SRVODI\3_1X\LSLENH.NLM
		 COPY A:\NOVELL\SRVODI\3_1X\PATCHMAN.NLM
	
	4. Enter "exit" to log out of the session then press any 
	   key to return to the System Console prompt.
				     
III. Perform substeps IIIA. and IIIB. to configure the NetWare 3 
     server to use the EtherWORKS NetWare 3/4 ODI server driver.

     A. With the NetWare 3 server running, edit the STARTUP.NCF 
	file using the INSTALL Program. 
	 
	1. From the System Console, load INSTALL:

	      :LOAD INSTALL

	2. Select "System Options."
	 
	3. Select "Edit STARTUP.NCF file."
	 
	4. Add the following SET parameter to set the proper packet
	   size.
	
	   a. If installing on NetWare 3.11 or 3.12:

		 set maximum physical receive packet size = 1520
	   
	5. Save the file with the changes.  Answer "Yes" to the 
	   exit prompt.

     B. You can automatically load the server driver by adding the 
	appropriate instructions to the AUTOEXEC.NCF file.  You can 
	also issue these commands directly from the System Console.
     
	1. While still in the INSTALL program, select "Edit 
	   AUTOEXEC.NCF file."  Add the following lines to 
	   AUTOEXEC.NCF to automatically load and bind the new 
	   driver every time the server is brought up:

	   a. If you installed the driver files on NetWare 3.12 
	      using Step IIA1., enter the following commands:

		 LOAD C:\DC21x4 slot=1 frame=ETHERNET_802.2
		 BIND IPX TO DC21x4 net=00000001

	   b. If you installed the driver files on NetWare 3.11 
	      using Steps IIA1. and IIA2., enter the following 
	      commands:

		 LOAD C:\LSLENH
		 LOAD C:\DC21x4 slot=1 frame=ETHERNET_802.2
		 BIND IPX TO DC21x4 net=00000001

	   c. If you installed the driver files on NetWare 3.12 
	      using Step IIB3a., enter the following commands:

		 LOAD DC21x4 slot=1 frame=ETHERNET_802.2
		 BIND IPX TO DC21x4 net=00000001

	   d. If you installed the driver files on NetWare 3.11 
	      using Steps IIB3a. and IIB3b., enter the following 
	      commands:

		 LOAD LSLENH
		 LOAD DC21x4 slot=1 frame=ETHERNET_802.2
		 BIND IPX TO DC21x4 net=00000001

	   A drive path is not included for the load statements in 
	   the third and fourth examples.  This is because the 
	   DC21x4.LAN driver files are copied to the SYS:SYSTEM 
	   directory, which is the NetWare 3.1X default server path.
       
	   In the above examples, note that LSLENH.NLM is only 
	   loaded under NetWare 3.11.  Also, note that PATCHMAN.NLM 
	   is auto-loaded when loading LSLENH.NLM.  Similarly, 
	   loading DC21x4.LAN auto-loads ETHERTSM.NLM which in turn 
	   auto-loads MSM31X.NLM.  This allows for fewer load 
	   statements in the AUTOEXEC.NCF file and less opportunity 
	   for driver load errors.

				     NOTE
	   Before saving the AUTOEXEC.NCF file, it is important to 
	   verify that no older NetWare 3 server drivers are loaded 
	   prior to loading LSLENH.NLM and/or MSM31X.NLM.  Even 
	   though older NetWare 3 server drivers do not require the 
	   LSLENH patch or MSM31X, unexpected behavior may result if 
	   LSLENH or MSM31X are loaded after the driver.  If using 
	   both older NetWare 3 and newer NetWare 3/4 server 
	   drivers, be sure to load LSLENH.NLM and MSM31X.NLM 
	   separately before loading any drivers.

	   e. Save the file with the changes.  Answer "Yes" to the 
	      exit prompt.

IV.  Shut down the server by entering "DOWN" at the system console 
     and then enter "EXIT" to return to the DOS prompt.

V.   Follow the instructions in your adapter's "User Information" 
     document for connecting the controller to the network.

VI.  Restart the server.

     Enter the following command at the DOS prompt:

	SERVER

     The changes made to the STARTUP.NCF and AUTOEXEC.NCF files in 
     step III above take effect.

