README.TXT File
USB Ethernet Adapter Support for OS/2 Warp
Version 1.00
Febrauary 13, 2001
(c)  Copyright International Business Machines Corporation, 2001.
     All rights Reserved.

Contents
-----------
1.0 Introduction
2.0 Installation Instructions
3.0 Uninstall Instructions
4.0 Copyright and Trademark Information


1.0  Introduction
------------------

USB Ethernet adapters gives more mobility to laptop and also desktop
computers network connectivity. USB Ethernet adapter support resides on
the top of USB Base stack and requires this stack to be installed before
network support can be used.
OS/2 USB Ethernet support is limited to adapters based on Kawasaki LSI
KL5KUSB101 chipset. Support softeare was tested on 3COM USB Network
Interface (3C19250), D-Link Corp. USB Ethernet Adapter (DSB-650) and ADS
Technologies Inc. USB Ethernet Adapter (USB-10BT).

2.0  Installation Instructions
-------------------------------

Basic USB Device Driver Stack that consists of USB Host Controller Driver
(for example USB Universal Host Controller Driver USBUHCD.SYS) and USB
Driver (USBD.SYS) must be installed before the USB Ethernet Adapter Support
installation.

1.  The USB Ethernet adapter support software consists of the following
files:
    - USBETHR.OS2       NDIS compliant network adapter driver.
    - USBETHR.NIF       Network adapter configuration file
    - README.TXT        This file that you are reading
Copy these files to the hard disk or floppy disk.
2.  open MPTS - Network Adapters and Protocol Services (click right mouse
button on desktop, select 'System setup' menu, double click on MPTS icon in
System Setup window);
3.  press 'Configure' button;
4.  select 'LAN adapter and protocols'; and press 'Configure' button;
5.  press 'Other adapters' button; fill out path to USB Ethernet adapter
    driver files (use default path A: if support files are copied to floppy
    disk in drive A:) and press OK;
6.  update vendor/device IDs card parameters dialog; use the following
    identification IDs:
+-----------------------------------------------------+---------+---------+
|                    Adapter                          |Vendor ID|Device ID|
+-----------------------------------------------------+---------+---------+
|3COM USB Network Interface (3C19250) *               |   0506  |  03E8   |
|D-Link Corp. USB Ethernet Adapter (DSB-650)          |   2001  |  4000   |
|ADS Technologies Inc. USB Ethernet Adapter (USB-10BT)|   06E1  |  0008   |
+-----------------------------------------------------+---------+---------+
*Default adapter

7.  Add required protocols from the 'Protocols' list to the USB Ethernet
    adpater;
8.  Press 'OK' button to close 'Adapter and Protocol Configuration' dialog;
9.  Press 'Close' button to close 'Configure' dialog;
9.  Press 'Exit' button to close MPTS utility;
10. Reboot the operating system.

3.0  Uninstall Instructions
---------------------------
1.  open MPTS - Network Adapters and Protocol Services (click right mouse
    button on desktop, select 'System setup' menu, double click on MPTS icon in
    System Setup window);
2.  press 'Configure' button;
3.  select 'LAN adapter and protocols'; and press 'Configure' button;
4.  select all protocols associated with USB Ethernet adapapter in
    'Current Configuration' adapter list, press 'Remove' button for each
    protocol;
5.  select USB Ethernet adapapter in 'Current Configuration' adapter list,
    press 'Remove' button;
6.  Press 'OK' button to close 'Adapter and Protocol Configuration' dialog;
7.  Press 'Close' button to close 'Configure' dialog;
8.  Press 'Exit' button to close MPTS utility;
9.  Reboot the operating system.

4.0  Copyright and Trademark Information
----------------------------------------
The following terms are trademarks of International Business Machines Corporation
in the United States and/or other countries.
    IBM                         OS/2
Other company, product, and service names may be trademarks or service marks
of others.